Thanks for visiting our site!
Aluminum Fuel Cell
Checkout Ebay Auctions For The Cheapest Prices
 |
 Vintage MOON EELCO aluminum Fuel cell 5 gallon  US $149.95
|
 HHO 3/8" FLASHBACK ARRESTOR HYDROGEN FUEL CELL GENERATOR Flash BILLET ALUMINUM! US $24.99
|
| Powered by phpBay Pro |
Check out Amazon:
| Account limit of 2000 requests per hour exceeded. |
Here are some more information for Aluminum Fuel Cell:
Why Build Your Own Fuel Cell?
You can build your own fuel cell for a fraction of what it costs to buy a commercial fuel cell. Not only will your unit, if done correctly, produce the same results it could produce even better results. Having control of size and output can custom fit a fuel cell to your specific engine. Engines that were too small to fit commercial units can now house custom built units.
Built By BOB
Instead of spending thousands for a sticker, you can slap on your own claim to fame. After all your custom built fuel cell for your specific engine producing optimal results will probably put a grin on your face, and you'll want to claim it. Tweaking your fuel cell for those optimal results is where the true savings are. Every engine is different, and it's next to impossible to gauge the exact benefits your engine will receive. Here's how to gain control and start tweaking.
Plates/Wires
First of all you used 316L stainless steel for your anodes right? My first plates were aluminum and they shorted out from the build up of oxidation. It's worth noting that the positive plates/wires take the most abuse. This is due to the production of the oxygen, the positive side produces the HHO, the O of course is oxygen. So if your going to spend a little extra on your cell make your positive plates/wires a thicker gauge. You'll thank me later, and your fuel cell will last years. Use that 316L stainless and change the water after a couple runs, this will burn off any factory grease/oil left on the plates. You'll get more control less muck, until no muck at all.
Conductivity
Control your conductivity in your water. You can do this by using distilled water, not filtered and especially not mineral or tap. The minerals and chemicals are what make the water conductive. Water in itself is a poor conductor, here's where you get to control the electrical pull of your cell. When you start with a clean slate like distilled water you can adjust the amount of catalyst used to increase conductivity therefor taking control of electrical pull of your cell. The pull will increase as heat increases so you need to find that happy medium of HHO production and heat. Too hot and you get thermal runaway until your fuse blows. If you don't use a fuse, you'll melt your cell. That little 15 amp fuse is a great investment. When you produce a well built cell, and know how to adjust it, you can get up to 2 liters per minute of HHO and your cell will be luke warm.
Fuel Ratio
When your pumping out large amounts of HHO and not leaning back your fuel, your wasting fuel. Your wasting HHO and gasoline and or diesel. If you keep saturation below 4% you won't throw off any sensors. Anything above that and your sensors will read an error. Your sensors are basically overgrown thermometers and their information is read by your engine in voltage. You can gain control of this voltage information and lean back your fuel. Look into a good EFIE to gain control to the millivolt. If your running an older engine or motorcycle you probably already know which screw to twist to control your fuel to air ratio. You'll be amazed at how far you can lean back your fuel when running HHO. You'll also start to grin when you realize how much fuel your saving. A little HHO goes a long way.
Now go enjoy the smoother cooler ride, that costs you less at the pump and helps save our environment. If you haven't already, and you like added horsepower, miles per gallon and cleaner emissions, now would be a good time to build your own fuel cell.
Here are the top reviewed plans to build your own [http://www.squidoo.com/howtomakefuelfromwater] fuel cell.
Get my tips on FUEL CELL PLANS [http://www.squidoo.com/howtomakefuelfromwater] and enjoy added MPG cleaner exhaust and added HP.
How to Make a Homemade Solar Cell
Sunlight is commonly acknowledged as the simplest source of energy and we have long realized this fact by utilizing the benefits of solar power. Fossil fuels are being depleted at an accelerated rate and are expected to extinct very shortly and solar power is being deemed a blessing for humanity. Solar energy provides numerous benefits to the people. The most beneficial reason of using this energy source is that it can provide the energy demands for everyone on Earth.
It's also a natural form of power and it's accessible in abundance and can be exploited with no hesitancy as compared to different forms of energy. When accumulating solar energy, there are zero pollutants being created. This can aid vastly in curbing pollution and global climate change.
Enough chit-chat, here are the steps to create a homemade solar cell:
1. The most important thing that needs to be done is cooking the silicon. Silicon is extracted from silicon dioxide. Silicon dioxide is heated in an oven at very high temperatures in order for all the impurities to be removed. We keep repeating this process of heating, and eventually we finish up with 99.5% pure silicon. This is the standard purity that's needed for making solar cells.
2. The following step in this technique is the crystallizing of the silicon. During this process silicon is heated up so that it melts then boron is added. This uncommon additive provides the electrical foundation in the silicon. Then it gets charged with positive charge.
3. At this point of process, silicon is in shape of blocks of metal. Then they're cut into fine sheets. The thickness of the sheets should be in the range of 200-300 micrometers.
4. Now the sheets of silicon are engulfed into chemical water so that they can be charge with a negative charge. Then a layer of anti-reflection material is added. This is performed because it yields a black appearance to the cell that can help to maximize the solar power of the sun.
5. Finally, aluminum or silver connections are bonded on the photovoltaic cell so that they can be employed for carrying electrical energy.
For more detailed directions, go to http://www.squidoo.com/solarcabin for step-by-step pictures and a video guide on how to make a homemade solar cell.
About the Author
For more detailed directions, go to http://www.squidoo.com/solarcabin for step-by-step pictures and a video guide on how to make a homemade solar cell.
Fuel cells. Why do people use hydrogen and not solid aluminum for fuel cells.?
Aluminum has no hazards, does not need to be compressed(extra energy), and is a great capacitor of energy.
http://www.aluminum.org/Template.cfm?Section=Technology_QandA&template=/ContentManagement/ContentDisplay.cfm&ContentID=1159
Hi. Actually there are hazards. The end product, aluminum oxide, is a harsh abrasive and is not easy to dispose of whereas the H/O fuel cell produces only water.
Riverfest 2010 Set for Memorial Day Weekend
Riverfest 2010 will be held May 28-30 along the Arkansas River in downtown Little Rock and North Little Rock.
Thanks for visiting!
